 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| RW1026 Dot Matrix 48x4 LCD Controller / Driver Features * Operating voltage: 2.4V~5.2V * External resistor CR oscillator * External 256k Hz frequency source input * Selection of 1/2 or 1/3 bias, and selection of 1/2or 1/3 or 1/4 duty LCD applications * Power down command reduces power consumption * 48 x 4 LCD driver * Built-in 48 x 4 bit display RAM * IIC serial interface * 3-line/4-line (type A & type B) serial interface (SPI) * Internal LCD driving frequency source * Software configuration feature * Data mode and command mode instructions * R/W address auto increment * VRAB pin for adjusting VLCD operating voltage General Description The RW1026 is a 192 patterns (48x4), memory mapping, and multi-function LCD driver. The S/W configuration feature of the RW1026 makes it suitable for multiple LCD applications including LCD modules and display subsystems. Only two or three or four lines are required for the serial interface between the host controller and the RW1026. The RW1026 contains a power down command to reduce power consumption. Block Diagram 1 RockWorks Technology Corp. RW1026 Dot Matrix 48x4 LCD Controller / Driver Pad Assignment Chip size: 2463 x 1344 um Pad Size: 89.5 x 88.5 um Pad Pitch: 92.5~231.4 um Chip thickness: 482.6 um The IC substrate should be connected to VSS in the PCB layout artwork. 2 RockWorks Technology Corp. RW1026 Dot Matrix 48x4 LCD Controller / Driver CHIP LAYOUT PIN 1 3 RockWorks Technology Corp. RW1026 Dot Matrix 48x4 LCD Controller / Driver Pad Description Pad I/O Function Chip selection input for 3-SPI, 4-SPIwith pull-high resistor. When CSB is login high, the data and command read from or written to the RW1026 are disabled. The serial interface circuit is also reset. But if CSB is at logic low level and is input to the CSB pad, the data and command transmission between the host controller and the RW1026 are all enabled. READ clock input for 4-SPI (type B) with pull-high resistor. Data in the RAM of RW1026 are clocked out on the falling edge of the XRD signal. The clocked out data will appear on the DATA line. The host controller can use the next rising edge to latch the clocked out data. A0 pin for 4-line(type A)serial interface. A0=1: DATA A0=0: Command WRITE clock input for 4-SPI (type B) with pull-high resistor. Data on the DATA line are latched into the RW1026 on the rising edge of the XWR signal. Serial clock input (SCLK) pin for 3-line, 4-line (type A), and IIC interface. Serial data input/output with pull-high resistor. Negative power supply. Ground The OSC1 and OSC2 pads are connected to a external resistor if an RC oscillator is selected. If the system clock comes from an external clock source, the external clock source should be connected to the OSC1 pad. LCD power input. Positive power supply. LCD common output. LCD segment output. Reset pin with pull-up resistor, Initialized by setting RSTP to "L". Reset operation is performing at RSTP signal level. LCD voltage adjusting pin. Applies voltage between V0 and VSS using a split resistor. Interface selection pins with pull-up resistor IF1,IF0 ( 0 , 0 ) : IIC Interface ( 0 , 1 ) : 3-line Interface ( 1 , 0 ) : 4-line Interface (Type A) ( 1 , 1 ) : 4-line Interface (Type B) CSB I XRD(A0) I XWR(SCLK) DATA VSS OSC1 OSC2 VLCD VDD COM0-COM3 SEG0-SEG47 RSTP VRAB I I/O I O I O O I I IF1,IF0 I 4 RockWorks Technology Corp. |
Price & Availability of RW1026
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |